Root access is available.
As of February 2016, opFlow is distributed in a self-extracting download format that simplifies the installation process quite a bit. More information on running the installer can be found HERE: The Opmantek Installer
Transfer the opFlow installer onto the server in question, either by direct download from the Opmantek website, or from your desktop with
sftp or a similar file transfer tool.
Make a record of where you put the tarball (
root's home directory or /tmp are good locations).
Start the interactive installer and follow its instructions:
sudo sh ./opFlow-Linux-x86_64-3.0.2.run ++++++++++++++++++++++++++++++++++++++++++++++++++++++ opFlow (3.0.2) Installation script ++++++++++++++++++++++++++++++++++++++++++++++++++++++ This installer will install opFlow into /usr/local/omk. To select a different installation location please rerun the installer with the -t option. ...
/usr/local/omk, and the default configuration files are in
/usr/local/omk/conf, ready for your initial config adjustments.
/usr/local/omk/install.log, and subsequent upgrades or installations of other Opmantek products will add to that logfile.
After installation you may need/want to change the directories that flows are stored in, the ports the flows are coming in on, etc. Please read the sections below for more.
On most platforms nfdump uses the classic init script /etc/init.d/nfdump, normally accessed via the
service helper, e.g.
service nfdump stop or
The init script contains defaults for the most essential options for the
It is recommended that you do not modify this init script, as upgraded nfdump packages may very well replace it.
Instead you should make use of the override file that is appropriate for your platform, and add values for (only) those options that you want to change.
On CentOS/RedHat, you need to create or modify
/etc/sysconfig/nfdump, on Debian/Ubuntu the correct file is
/etc/default/nfdump. Please note that this override file wins over the defaults that the init script sets.
Here is a list of the defaults as provided by the init script:
# best way to configure these is via /etc/default/nfdump or /etc/sysconfig/nfdump, # DATA_BASE_DIR needs to be the same as "<opflow_dir>" in opCommon.nmis DATA_BASE_DIR="/var/lib/nfdump" DATA_ROTATE_INTERVAL=300 NETFLOW_PORT=9995 PIDFILE=/var/run/$NAME.pid
To to change port and spool directory to your preferred settings, edit
/etc/default/nfdump so that it contains the following entries:
# non-standard config settings for nfdump # this directory was used by opFlow 2.X DATA_BASE_DIR=/data/opflow NETFLOW_PORT=12345
When that's done, you need to restart the
nfdump service to activate your configuration:
sudo service nfdump restart.
The most recent nfdump packages in Debian come with a problematic systemd service file (see bug Debian Bug 843602) which completely ignores /etc/default/nfdump.
Until that is resolved, we recommend that you disable the nfdump systemd service and have the system fall back to using sysv init scripts, combined with the nfdump init script that was shipped with opFlow (which is available as
A symptom of that issue would be that
nfcapd is running with data directory
/var/cache/nfdump, is listening on a port that is neither 9995 nor your NETFLOW_PORT from /etc/default/nfdump, does not include the
"-T all" argument to enable netflow extensions, and does not include the
-t argument for data rotation.
ps ax|fgrep nfcapd # good: that one honours custom settings as it should 1583 ? S 0:47 /usr/bin/nfcapd -D -T all -l /data/opflow -t 120 -P /var/run/nfcapd.pid -p 12345 # BAD: that's an nfcapd with undesireable hardcoded arguments 1257 ? S 0:00 /usr/bin/nfcapd -D -l /var/cache/nfdump -P /var/run/nfcapd.pid -p 2055
The forced switch to SysV init script can be made by running the following commands as
root (ie. under
sudo bash or the like):
service nfdump stop dpkg-divert --rename --divert /lib/systemd/system/nfdump.service.disabled --add /lib/systemd/system/nfdump.service rm -f /etc/systemd/system/nfdump.service /etc/systemd/system/multi-user.target.wants/nfdump.service systemctl daemon-reload # note that this will only work fully if you use the nfdump init script from /usr/local/omk/install/nfdump.init.d! service nfdump start
The following changes can be made in the opCommon configuration file /usr/local/omk/conf/opCommon.nmis
It is important that the <opflow_dir> in opCommon.nmis matches the DATA_BASE_DIR in the nfdump configuration
'<opflow_dir>' => '/data/opflow', # or '/var/lib/nfdump' to match the default shipping config
NMIS integration enables the resolution of Interface indexes to Interface Names. The association to an NMIS node enables opFlow to look up the interface indexes which the traffic is flowing to and from. Note the agents are a list of the IP addresses from which flows are received. opFlow will automatically update Agent->Node links once an hour, at this time interface information will also be updated, the update can also be triggered from the GUI using System->Sync Agent/Node Data. Associating to an NMIS node enables opFlow to look up the interface indexes which the traffic is flowing to and from.
Linking with opCharts/NMIS can be done to an NMIS instance on the same server (Local) or can integrate to a remote instance of opCharts. If you are running opCharts3 as the remote it must not be a Primary instance it must be a normal poller instance. If you are running opCharts4 the remote server can be a poller or a Primary.
If you are linking to a local omkd do not use a remote connection.
If the config setting 'opflow_opcharts_url_base' is left blank, opFlow will attempt to load node information from a local NMIS server found at 'nmis_dir' => '/usr/local/nmis8'
Remote integration requires setting 3 config items, these are used so the opFlow server can access an opCharts server. When this is working the GUI will show ifDescr and Descriptions in the agent selector, and when filtering on an agent/interface will display the interface info panel.
The two servers must have the same value for <omk_url_base> (which is not often changed)
# NOTE: no trailing slash 'opflow_opcharts_url_base' => "http://someserver.tld", # base for omk, do not connect to localhost this way, use local nmis integration 'opflow_opcharts_user' => "nmis", # needs ro-access 'opflow_opcharts_password' => "nm1888",
There are two high volume controls for opFlow, one for the backend and one for the frontend.
'opflow_high_volume' => 1, 'opflow_gui_high_flow_volume' => 1, 'opflow_gui_no_flows_over_time_graph' => 1, 'opflow_gui_display_other' => 0,
opflow_high_volume will cause opflowd to insert pre-aggregated flows if set, raw flows if not. Currently the GUI has no way of displaying raw flows so this is enabled by default.
opflow_gui_high_flow_volume will force the GUI to show a simplified/optimized index page, it can also be viewed by setting ?simple=1 on the index page, it is enabled by default.
opflow_gui_no_flows_over_time_graph will remove the flows over time graph from the index page, this is off by default.
opflow_gui_display_other tells opFlow if all flows outside of the TopN should be summarised into an "other" entry, this is off by default
The graph that show flows over time can display 2 modes: the default shows the number of octets/packets in the current time slice, the second mode makes the graph display the data in octets/second or packets/second. To enable the second mode change the following config variable to 1:
'opflow_gui_graph_over_time_per_sec' => 1
opFlowSP 1.0.9 introduced 3 new configuration items:
'opflow_gui_hide_interface_performance_graphs' => 0, # Custom agent button #'opflow_gui_agent_custom_button_text' => 'Button Text', #'opflow_gui_agent_custom_button_url' =>'https://example.com/omk/opCharts/inventory/interfaces',
opflow_gui_hide_interface_performance_graphs is used to hide or show the button "Interface Performance Graphs". Default is 0 to show the button. Set to 1 to hide the button.
opflow_gui_agent_custom_button_text and opflow_gui_agent_custom_button_url are set together to add a button with a custom link to be visible to the right of "Interface Performance Graphs".
Possibility to set the octet format to MegaBytes (MB) or Megabits (Mbits) using the configuration item opflow_gui_octet_display_multiplier.
'opflow_gui_octet_display_multiplier' => 0.000000953674316, 'opflow_gui_octet_display_multiplier' => 0.000008,
After making changes to the config make sure to restart all opFlow daemons.
service nfdump restart service omkd restart service opflowd restart
A basic router configuration guide for exporting flow data is available here.
opFlow attempts to resolve all ip address so DNS settings must be correct. Be sure to verify that DNS settings are appropriate:
cat /etc/resolv.conf # verify the listed nameservers and search order works, # using dig, nslookup or host
If you have very large numbers of distinct IP addresses in your flows you should DISABLE DNS lookup, change 'opflow_resolve_endpoint_dns' => 'true', to false in /usr/local/omk/conf/opCommon.nmis to speed up performance. Each of the opflow processes will have to wait for each of the DNS lookups which means you will have a large number processes waiting for DNS to return information. This is especially true on internet traffic as resolution will require a PTR lookup through to the SOA for that IP which could take a while.