You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 8 Next »

Overview

Some customers may benefit by moving files that NMIS reads/writes to very often to a RAM Disk.  We have seen this improve performance on pollers that have shared storage and 2,000+ nodes provisioned.  The concept is that NMIS will be able to read/write to RAM faster than the shared storage.  Most of the files that NMIS touches very often are found in the nmis8/var directory.

Procedure

Step #1 - Determine Space Required

There are two questions that quickly come to mind:

  • How big should the RAM disk be?
  • How much RAM is available?

Check how much space nmis8/var is currently using; minus the nmis8/var/events directory.  We will keep the nmis8/var/events directory on a hard drive because it contains stateful event history; we don't want to loose these if the server is rebooted. 

[root@TEST var]# pwd
/usr/local/nmis8/var

[root@TEST var]# du -hs
2.6G    .

[root@TEST events]# pwd
/usr/local/nmis8/var/events

[root@TEST events]# du -hs
1.7G    .

In this example we notice that the nmis8/var directory minus the nmis8/var/events directory is approximately 900MB.  It appears that a RAM disk of 1GB would be sufficient.

How much RAM is available?

[root@TEST events]# free
             total       used       free     shared    buffers     cached
Mem:      37016616   25990916   11025700       1796     861860   15379752
-/+ buffers/cache:    9749304   27267312 
Swap:      4169724     558624    3611100

In the example above there appears to be 11GB of RAM available.

Step #2 - Create the RAM disk

The following commands will create the RAM disk, keep events on the hard drive, and ensure permissions are not lost.   These commands should also need to be added to a script that runs at boot time.  On Centos 6 /etc/rc.d/rc.local works well.

mount -t tmpfs -o size=1000M tmpfs /media/ramdisk/
mkdir -p /media/ramdisk/nmis8/var
ln -s /data/nmis8/var/events /media/ramdisk/nmis8/var
/usr/local/nmis8/admin/fixperms.pl

Use the df command to confirm that the ramdisk was created.

[root@TEST]# df -h
Filesystem            Size  Used Avail Use% Mounted on
/dev/mapper/vg_nmis64-lv_root
                       16G   11G  4.1G  73% /
tmpfs                 5.9G     0  5.9G   0% /dev/shm
/dev/sda1             477M   75M  377M  17% /boot
/dev/mapper/vg_nmis64_data-lv_data
                      246G   95G  139G  41% /data
/dev/mapper/vg_nmis64-lv_var
                       20G   10G  8.3G  55% /var
tmpfs                1000M   30M  971M   3% /media/ramdisk

 

Step #3 - Disable NMIS

We need to disable NMIS so that it will not attempt to modify the files as we are point nmis8/var to the new RAM disk.  Comment out any jobs in /etc/cron.d/nmis that may run during the next 20 minutes.  Here's an example of a couple cron jobs that should be commented out.

######################################################
# Run (selective) Statistics and Service Status Collection often
#* * * * *       root     /usr/local/nmis8/bin/nmis.pl type=collect mthread=true ; /usr/local/nmis8/bin/nmis.pl type=services mthread=true
######################################################
# Run Summary Update every 5 minutes
#*/5 * * * *     root     /usr/local/nmis8/bin/nmis.pl type=summary

Option 42b

[root@TEST]# touch /usr/local/nmis8/conf/NMIS_IS_LOCKED

After these jobs have been disabled, check the server for any nmis.pl processes

[root@TEST]# ps -ef | grep nmis.pl

When none are found continue

Step #4 - Point nmis8/var at the RAM Disk

Since we are planning to put a sym link in /usr/local/nmis8/ for /var pointing at the new RAM disk; verify that in /usr/local/nmis8/conf/Config.nmis nmis8/var points to /usr/local/nmis8/var.  Here's a sample of the directories configuration in that file.

/usr/local/nmis8/conf/Config.nmis
  'directories' => {
    '<menu_base>' => '<nmis_base>/menu',
    '<nmis_admin>' => '<nmis_base>/admin',
    '<nmis_backups>' => '<nmis_data>/backups',
    '<nmis_base>' => '/usr/local/nmis8',
    '<nmis_bin>' => '<nmis_base>/bin',
    '<nmis_cgi>' => '<nmis_base>/cgi-bin',
    '<nmis_conf>' => '<nmis_base>/conf',
    '<nmis_data>' => '<nmis_base>',
    '<nmis_logs>' => '<nmis_base>/logs',
    '<nmis_menu>' => '<nmis_base>/menu',
    '<nmis_models>' => '<nmis_base>/models',
    '<nmis_var>' => '<nmis_data>/var',
    'config_logs' => '<nmis_logs>/config',
    'database_root' => '<nmis_data>/database',
    'json_logs' => '<nmis_logs>/json',
    'log_root' => '<nmis_logs>',
    'mib_root' => '<nmis_base>/mibs',
    'plugin_root' => '<nmis_conf>/plugins',
    'report_root' => '<nmis_base>/htdocs/reports',
    'script_root' => '<nmis_conf>/scripts',
    'web_root' => '<nmis_base>/htdocs'
  },

Create the sym link in /usr/local/nmis8/ sending /var to the RAM disk.

ln -s /media/ramdisk/nmis8/var/ /usr/local/nmis8

Step #5 - Re-enable NMIS

Uncomment any cron jobs that had been commented out previously in step #4.

Option 42c

[root@TEST]# rm /usr/local/nmis8/conf/NMIS_IS_LOCKED

 

Step #6 - Verify

Take a look at the /usr/local/nmis8/var directory and confirm that node.json and view.json files have been created.  Also verify that the NMIS GUI is functioning normally.

 

  • No labels